Package: flashrom
Priority: extra
Section: electronics
Installed-Size: 637
Maintainer: Uwe Hermann <uwe@debian.org>
Architecture: armhf
Version: 0.9.7+r1852-1.1
Recommends: dmidecode
Depends: libc6 (>= 2.13-28), libftdi1 (>= 0.20), libpci3 (>= 1:3.1.9-2)
Filename: pool/main/f/flashrom/flashrom_0.9.7+r1852-1.1_armhf.deb
Size: 364756
MD5sum: 99cc1d08d4f6ec4bbea7b568e956b4fb
SHA1: 1d374a2c45a4525f304b3c8b4d557991b623d6aa
SHA256: 80b55cd11b91d0c7e1d8f9fddd62235b2d75f8f1161a305ab90c9cd9596956f3
Description: Identify, read, write, erase, and verify BIOS/ROM/flash chips
 flashrom is a tool for identifying, reading, writing, verifying and erasing
 flash chips. It's often used to flash BIOS/EFI/coreboot/firmware/optionROM
 images in-system using a supported mainboard, but it also supports flashing of
 network cards (NICs), SATA controller cards, and other external devices which
 can program flash chips.
 .
 It supports a wide range of DIP32, PLCC32, DIP8, SO8/SOIC8, TSOP32/40/48,
 and BGA chips, which use various protocols such as LPC, FWH, parallel
 flash, or SPI.
 .
 The tool can be used to flash BIOS/firmware images for example -- be it
 proprietary BIOS images or coreboot (previously known as LinuxBIOS) images.
 .
 It can also be used to read the current existing BIOS/firmware from a
 flash chip.
 .
 Currently supported programmers include:
 .
 * internal (default, for in-system flashing in the mainboard)
 * dummy (virtual programmer for testing flashrom)
 * nic3com (for flash ROMs on 3COM network cards)
 * nicrealtek (for flash ROMs on Realtek network cards)
 * nicsmc1211 (for flash ROMs on RTL8139-compatible SMC2 network cards)
 * nicnatsemi (for flash ROMs on National Semiconductor DP838* network cards)
 * nicintel (for parallel flash ROMs on Intel 10/100Mbit network cards)
 * nicintel_spi (for SPI flash ROMs on Intel Gigabit network cards)
 * gfxnvidia (for flash ROMs on NVIDIA graphics cards)
 * drkaiser (for flash ROMs on Dr. Kaiser PC-Waechter PCI cards)
 * satasii (for flash ROMs on Silicon Image SATA/IDE controllers)
 * satamv (for flash ROMs on Marvell SATA controllers)
 * atahpt (for flash ROMs on Highpoint ATA/RAID controllers)
 * ft2232_spi (for SPI flash ROMs attached to an FT2232/FT4232H
 family based USB SPI programmer), including the DLP Design DLP-USB1232H,
 FTDI FT2232H Mini-Module, FTDI FT4232H Mini-Module, openbiosprog-spi,
 Amontec JTAGkey/JTAGkey-tiny/JTAGkey-2, Olimex ARM-USB-TINY/-H,
 Olimex ARM-USB-OCD/-H, TIAO USB Multi-Protocol Adapter (TUMPA),
 GOEPEL PicoTAP, and FIC OpenMoko Neo1973 Debug board.
 * serprog (for flash ROMs attached to a programmer speaking serprog),
 including AVR flasher by Urja Rannikko, AVR flasher by eightdot,
 Arduino Mega flasher by fritz, InSystemFlasher by Juhana Helovuo,
 and atmegaXXu2-flasher by Stefan Tauner.
 * buspirate_spi (for SPI flash ROMs attached to a Bus Pirate)
 * dediprog (for SPI flash ROMs attached to a Dediprog SF100)
 * rayer_spi (for SPI flash ROMs attached to a RayeR parport based programmer)
 * pony_spi (for SPI flash ROMs attached to a SI-Prog serial port
 bitbanging adapter)
 * ogp_spi (for SPI flash ROMs on Open Graphics Project graphics card)
 * linux_spi (for SPI flash ROMs accessible via /dev/spidevX.Y on Linux)

Package: python-rpi.gpio
Source: rpi.gpio
Priority: optional
Section: python
Installed-Size: 192
Maintainer: Ben Croston <ben@croston.org>
Architecture: armhf
Version: 0.6.2~wheezy-1
Depends: libc6 (>= 2.13-28), libgcc1 (>= 1:4.4.0), python (>= 2.6.6-7~), python (<< 2.8)
Filename: pool/main/r/rpi.gpio/python-rpi.gpio_0.6.2~wheezy-1_armhf.deb
Size: 48242
MD5sum: 500d5ebcf24484e50377c8403af4b061
SHA1: 5cebb81632e73d1f3036f2bbb696727149b980e5
SHA256: ff1881326d85554446fc6b192135726972ded5b37d85df6a4fc83b0f8dec41e3
Description: Python GPIO module for Raspberry Pi
 This is the RPi.GPIO Python module, for supporting GPIO on a
 Raspberry Pi

Package: python3-rpi.gpio
Source: rpi.gpio
Priority: optional
Section: python
Installed-Size: 101
Maintainer: Ben Croston <ben@croston.org>
Architecture: armhf
Version: 0.6.2~wheezy-1
Depends: libc6 (>= 2.13-28), libgcc1 (>= 1:4.4.0), python3 (>= 3.2.3-3~), python3 (<< 3.3)
Filename: pool/main/r/rpi.gpio/python3-rpi.gpio_0.6.2~wheezy-1_armhf.deb
Size: 28352
MD5sum: f7f4223ab7439853ec32ae024ddd628f
SHA1: cc961138fc79f82d7aabbffce27e0e8d6d10892a
SHA256: ab6be0fc86d3271faba0bf2bcfd94fd8057dfb8236c953d5be428c7d3c2bbae8
Description: Python 3 GPIO module for Raspberry Pi
 This is the RPi.GPIO Python 3 module, for supporting GPIO on a
 Raspberry Pi